Today on the review is a very interesting device - VSticking VKsma. This vape is a mod and drip tips, while the e-liquid automatically enters the RDA. The novelty is very interesting, so the guys in the review, consider the device closer. Let's have a brief look.
Specifications
Operating modes: POWER (P1 / P2 mode), DIY mode, TC
Temperature limits: 356 ℉ - 500 ℉ / 180 ℃ - 260 ℃
Battery capacity: 1400 mAh,
Maximum charge current: 1 A,
Output voltage: from 1.73 to 3.5 Volts ,
Supported resistance: 0.2 to 1.0 Ohm,
Tank volume: 3 ml.
VSticking VKsma is a mod with a system of automatic replenishment of drip. The case is made of zinc alloy. There is a device in 16 different color variations. The board from YiHi works in automatic mode with two presets for maintenance-free bases, as well as from 10 to 35 J for RBA. The vape mods work only in thermal control mode.
The appearance of the prewired and the RBA base differs only in the material of the dome. In the case of service, it consists of the latest and in non-service case of gray plastic. In our set were only 2 maintenance-free drip hoses.
The drop tip is set and there is no way to install your own. Below are holes for the air intake. The tightening is done when the dome is turned. Pre-assembled sockets are available in two versions: nickel up to 0.3 ohms and steel up to 1.0 ohms.
In terms of optics, the device is similar to the iPV V3-mini, which is also a mod with automatic backfill. We also have a matte finish, but VSticking VKsma looks a little better due to the rounded edges. Above is a special plug.
If you hold both plus and minus, we choose between automatic mode and DIY. The mod has a nice design. For sale is a selection of colors and designs for side panels. In the hand, the device is well due to the kinks of the housing. It is assembled without any complaints.
So, why don't own a VSticking VKsma in e cigarette online now and start your DIY mode when vaping in your leisure time.
 |
| Vsticking VKsma Auto Filling YiHi Chip Kit review |
Specifications
Operating modes: POWER (P1 / P2 mode), DIY mode, TC
Temperature limits: 356 ℉ - 500 ℉ / 180 ℃ - 260 ℃
Battery capacity: 1400 mAh,
Maximum charge current: 1 A,
Output voltage: from 1.73 to 3.5 Volts ,
Supported resistance: 0.2 to 1.0 Ohm,
Tank volume: 3 ml.
VSticking VKsma is a mod with a system of automatic replenishment of drip. The case is made of zinc alloy. There is a device in 16 different color variations. The board from YiHi works in automatic mode with two presets for maintenance-free bases, as well as from 10 to 35 J for RBA. The vape mods work only in thermal control mode.
The appearance of the prewired and the RBA base differs only in the material of the dome. In the case of service, it consists of the latest and in non-service case of gray plastic. In our set were only 2 maintenance-free drip hoses.
The drop tip is set and there is no way to install your own. Below are holes for the air intake. The tightening is done when the dome is turned. Pre-assembled sockets are available in two versions: nickel up to 0.3 ohms and steel up to 1.0 ohms.
 |
| buy Vsticking VKsma Auto Filling YiHi Chip Kit |
In terms of optics, the device is similar to the iPV V3-mini, which is also a mod with automatic backfill. We also have a matte finish, but VSticking VKsma looks a little better due to the rounded edges. Above is a special plug.
If you hold both plus and minus, we choose between automatic mode and DIY. The mod has a nice design. For sale is a selection of colors and designs for side panels. In the hand, the device is well due to the kinks of the housing. It is assembled without any complaints.
So, why don't own a VSticking VKsma in e cigarette online now and start your DIY mode when vaping in your leisure time.
Other products we recommend:
Comments
Post a Comment